Grain-systems PNEG-1590 Uživatelský manuál stáhnout pdf (Strana 2)

Revision 08

Page 2 of 3

Dryer Pre-fire Checklist

___ Check wiring in control boxes (Jumpers, loose wires, and strands).

___ Check wiring to the main power supply.

___ Check location of 1FI and 2FI wires, make sure 1 is on L1 and 2 is on L3.

___ Capacitor is installed on moisture control light (2000 series only).

___ Check all overloads are set at the rated amperage listed on motors rating plate.

___ Check wiring in fan boxes

___ Check fan overloads are set at the rated amperage listed on the motors rating plate.

___ Check direction of flow on all solenoids and regulators.

___ Perform a Dielectric Strength (Hi-Pot) test in accordance with work instruction QSD-000152.R00. ___ Pass, ___ Fail

___ Perform a Grounding Continuity test in accordance with work instruction QSD-000151.R00. ___ Pass, ___ Fail

___ Apply required power.

___ Install newest version of software into the computer. Version #_______

___ Check switch wiring using feature in program (Vision).

___ Check switch lights for correct colors.

___ Set dip switches on back of display I/O. 2 & 3 on for GSI, 2 on for FFI.

___ Put correct model number of dryer into computer.

___ Check LCD for backlighting.

___ Do all operating lights work?

___ Overload amp range: Load _______, Unload _______, Fan #1 _______, #2 _______, #3 _______, #4 _______, #5 _______, #6 _______.

___ Auxiliary overload amp range: Unload _________ Load _________.

___ Check 12 volt output. _________ Volts.

___ Check that grain and plenum temperature read out is correct.

___ Check the SCR drive resistor for the proper size.

___ Check outside light.

___ Check motor rotation: Unload (CCW) _________Load (CW) _________ Metering rolls (CW) _________ Load CCW for FF _________.

___ Ensure Aux contactor engages when load is on

___ Ensure Aux contactor engages when unload is on

___ Check Unload Auger for Excessive Vibration.

___ Metering roll RPM and BPH are displayed and counting.

___ Check 2 speed operation with moisture control on for low speed and off for high speed.

___ Turn pots on main I/O board fully to the right.

___ Set SCR board pots IR to 10 o’clock and CL to 4 o’clock.

___ Adjust minimum voltage for SCR drive to 9 volts @ 0 on pot display for vision set 9 volts @ 50 for (2000 series)

___ Adjust maximum voltage for SCR drive to 180 volts @ 1000 on pot display

___ Check for unload auger clean out time delay after SCR has shut off meter rolls.

___ Check load motor on and off operation with the mercury switch with delay.

___ Check the out of grain timer is working.

___ Check motor running amps: Unload ___________amps. Load _____________amps.

___ Run fans with airswitch on to make sure it is wired correctly.

___ Check the fan motor(s) running amps: Fan #1 _______ Fan #2 _______Fan #3 _______Fan #4 _______Fan #5 _______Fan #6 _______

___ Check total running amps of the dryer: _______amps.

___ Is there a 5 second time delay between each fan start-up.

___ Check 20 second safety on burners with burner on but with no gas attached. #1 ____ #2 ____ #3 ____ #4 ____ #5 ____ #6 _____

Dryer Burner Operation Checklist

___ Adjust the vaporizer coil (LP units only). Burner #1 ______ #2 ______ #3 ______ #4 ______ #5 ______ #6______

___ Operate dryer in continuous flow mode.

___ Do all burners light: Burner #1 ______ #2 ______ #3 ______ #4 ______ #5 ______ #6 ______

___ Adjust gas pressure ______ 3 & 10 lbs. for LP, ______ 2 & 6 lbs. for natural gas.

___ Check burner pipe trains for gas leaks: Burner #1 ______ #2 ______ #3 ______ #4 ______ #5 ______ #6 ______

___ Do all burners cycle from high to low: Burner #1 ______ #2 ______ #3 ______ #4 ______ #5 ______ #6 ______

___ Cycle burner six times by using the burner control switch

___ Cycle burner six times by setting the computer to on/off fire

___ Operate dryer in staged batch mode 2 times.

___ Does moisture control hold at the end of the dry cycle?

___ Video dryer with all motors and burners on.

___ Burn all gas out of pipe train.

Safety Shutdown Checklist

___ Housing high limit for fan #1 ______ #2 ______ #3 ______ #4 ______ #5 ______ #6 ______

___ Vapor high limit for each fan (On LP units only) #1 ______ #2 ______ #3 ______ #4 ______ #5 ______ #6 ______

___ Fixed grain high limits: Lower ____ Middle ____ Upper ____.

___ Check discharge switch with unload running to check discharge vibration and ensure proper shut down

___ Remove grain sensor wires to ensure proper wiring

___ Auxiliary user safety.

___ Plenum high limit for each plenum chamber.

___ Motor overload.

___ Make sure all covers are on boxes and housing high limits

1 2 3

Komentáře k této Příručce

Žádné komentáře

Grain-systems PNEG-1590 Uživatelský manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Kondicionéry Grain-systems PNEG-1590