Grain-systems PNEG-349 Uživatelský manuál

SERVICE PLATFORM &revised 2004revised 2004revised 2004revised 2004revised 2004PNEG-349REVTWO & THREEMODULE STACK DRYER MODELSSTIFFENER INSTA

10Service Platform & StiffenerPLATFORM INSTALLATION7. Use two flathead allen capscrewsand connect the center floorsupport, D61-0062, to the fronta

11Service Platform & StiffenerPLATFORM INSTALLATIONInstall the floor support anglesas follows:1. Use two flathead allen capscrewsand connect the l

12Service Platform & StiffenerPLATFORM INSTALLATIONInner Guard RailInstall the inner guard rail supportsand related parts within platformpackage n

13Service Platform & StiffenerPLATFORM INSTALLATIONFigure 15: Connecting outer front toe board to guard rail support channels.Figure 16: Connecti

14Service Platform & StiffenerPLATFORM INSTALLATION1. Connect one left-hand outer reartoe boards.2. Connect the left-hand inner reartoe board.3. C

15Service Platform & StiffenerPLATFORM INSTALLATIONFigure 19: Installing front long floor panel.6. Connect the right-hand inner toeboard.7. Place

16Service Platform & StiffenerPLATFORM INSTALLATIONFigure 21: Installation of the short wide floor panel, left-hand outer rear toeboards and hinge

17Service Platform & StiffenerPLATFORM INSTALLATIONPlatform Guard RailsUse 5/16" x 3/4" bolts and install plat-form guard rails within p

18Service Platform & StiffenerPLATFORM INSTALLATIONFigure 25, right: Installing accessdoor. Figure 26, below: Make suredoor opens freely and lies

19Service Platform & StiffenerPLATFORM INSTALLATIONFigure 27: Close-up of access door clip on guard rail.Figure 28: Check to make sure every bolt

2Service Platform & Stiffener

20Service Platform & StiffenerPLATFORM INSTALLATIONFigure 29: Finished platform on an Airstream upper module.

21Service Platform & StiffenerPLATFORM INSTALLATIONFigure 30: Ladder side view of platform on a dryer module.

22Service Platform & Stiffener PLATFORM INSTALLATIONService Platform PartsPlatform Support Channels and Floor Support AnglesQuantityPer Platform21

23Service Platform & StiffenerPLATFORM INSTALLATIONFigure 31: Breakdown of platform parts.Items 9 & 11 are nowone part.

24Service Platform & StiffenerPLATFORM INSTALLATIONFigure 32: Breakdown of platform floor parts.

25Service Platform & StiffenerSTIFFENER INSTALLATION

26Service Platform & StiffenerSTIFFENER BASKET LOCATIONFigure 33: Location of stiffener angles on basket based on lenght.

27Service Platform & StiffenerSTIFFENER EXPLODED VIEWFigure 34: Exploded view of stiffener.

28Service Platform & StiffenerSTIFFENER ASSEMBLY GeneralThis is a guide for assembling and mounting the newStack Dryer Sti

29Service Platform & StiffenerThe Second and Third Module Stiffeners are as-sembled the same way as the base module with onlyminor variations. Fo

3Service Platform & StiffenerInstallation & Safety...

30Service Platform & StiffenerEXCEPT FOR THE ABOVE STATED EXPRESS LIMITED WARRANTIES, GSI MAKES NO WAR-RANTY OF ANY KIND, EXPRESSED OR IMPLIED, IN

1004 E. Illinois St., Box 20Assumption, IL 62510-0020phone: 217-226-4421fax: 217-226-4420www.grainsystems.comOctober 1998REVISED August 2004

4Service Platform & StiffenerINSTALLATION & SAFETYWARNING! BE ALERT!Personnel operating or workingaround equipment should read thismanual. T

5Service Platform & StiffenerPLATFORM INSTALLATION

6Service Platform & StiffenerPLATFORM INSTALLATIONAirstream service platform units aredesigned for use with Airstream twoand three module grain dr

7Service Platform & StiffenerPLATFORM INSTALLATIONFigure 4: Attaching side channels.Figure 3: Bolting reinforcement plate to main support channel.

8Service Platform & StiffenerPLATFORM INSTALLATIONFigure 5: Placing rear tie angle on platform.5. Position the rear angle tie, D01-2034, and conne

9Service Platform & StiffenerPLATFORM INSTALLATIONFigure 7: Close-up of rear portion of frame.Figure 8: Attaching front channel.